Rotel RSP-1069 Bedienungsanleitung PDF herunterladen (Seite 35)

English

Remote Zone Operation

The RSP-1069 provides multi-zone capabil-

ity, allowing you to enjoy music and operate

the system from a second, third, and fourth

room. From the remote location, you can se

lect a source component (independent from

the source playing in the main room), adjust

the volume level in the remote zone, and op

erate the source components.

To use the remote zone capability, you need

additional components: a pair of speakers

installed in the remote zone, an ampliﬁer

to drive them, an optional TV monitor for

video signals, and a third-party IR repeat-

er system.

Zone 2, 3, or 4 can be controlled from the

main room using RSP-1069’s front panel or

remote control ZONE button. Operation from

the remote zone requires the installation of

an infrared repeater system (from Rotel or

other suppliers) which relays infrared remote

control commands from remote zone to the

ZONE 2–4 REM IN connectors on the back

of the RSP-1069.

Several points about the remote zone func

tion:

• There are two options for the remote zone

output level, selectable from the ZONE SET

UP conﬁguration menu. VARIABLE output

provides full adjustment of the volume level.

FIXED output disables the remote zone vol

ume control with the output permanently set

to a speciﬁed level. This might be useful for

sending a line level signal to a preamp or

integrated amp with its own volume control

or to a distribution ampliﬁer with multiple

volume controls.

• The RR-1060 remote control supplied with

the RSP-1069 will operate the remote zones

if used with a repeater system from the

remote zone. It can also be programmed

to operate Rotel source components via

the RSP-1069’s IR OUT jack.

• Any source component connected to the

RSP-1069’s analog inputs can be sent to

the remote zone outputs. The remote zones

operate independently of the main room.

You can select a different source or adjust

remote zone volume without affecting the

MAIN outputs in any way.

• Avoid sending the same infrared command

to the RSP-1069 front panel sensor and a

remote zone repeater at the same time.

This means that remote zones must be

in a different room from the RSP-1069.

Remote Zone Power On/Off

Once master power is applied to the unit

by pressing the rear panel POWER switch

button, the RSP-1069 provides independent

power on/off operation for the remote zones.

Pressing the remote control ON/OFF buttons

in the main room activates or deactivates the

RSP-1069 in the main room only and has no

effect on the remote zones. Conversely, ac

tivating or deactivating Zone 2, 3, or 4 has

no effect on the main listening room. How-

ever, placing the rear panel master POWER

switch in the OFF position completely shuts

off the unit, for all zones.

NOTE: For proper power on and off operation

with remote zones, the RSP-1069’s power

mode should be set to the factory default

STANDBY setting or to the DIRECT setting

using the OTHER OPTIONS menu described

in the Setup section of this manual.

Controlling Zones 2–4

from the Main Room

You can control Zones 2–4 from the main room

using front-panel or remote control buttons

to activate or deactivate Zones 2–4, change

input sources, and adjust the volume. Con

trolling Zone 2, 3 or 4 from the main room is

accomplished by pressing the SEL button on

the front panel or REC button on the remote

two or more times, putting the RSP-1069 in

Zone 2, 3 or 4 control mode temporarily.

When Zone 2, 3 or 4 status is displayed,

the OSD and/or front-panel displays show

the current source selection and volume in

that zone for ten seconds, during which time

you can use the front panel VOLUME control

and INPUT buttons to change the ZONE 2,

3 or 4 settings.

To turn a remote zone on or off:

1. Press the front panel SEL button or remote

REC button two or more times until the de

sired Zone 2, 3, or 4 status appears in

the OSD and front panel displays.

2. Within 10 seconds, press the front panel

or remote ZONE button to toggle the re

mote zone on or off.

3. Following 10 seconds with no commands,

the RSP-1069 reverts to normal opera

tion.

To change a remote zone input

source:

1. Press the front panel SEL button or remote

REC button two or more times until the de

sired Zone 2, 3, or 4 status appears in

the OSD and front panel displays.

2. Within 10 seconds, press one of the IN

PUT buttons to select a new source for the

remote zone. The name of the selected

source appears in the display. Instead of

pressing an INPUT button, you can also

push the +/– buttons on the remote to step

through the inputs.

3. Following 10 seconds with no commands,

the RSP-1069 reverts to normal opera-

tion.

To change a remote zone volume:

1. Press the front panel SEL button or remote

REC button two or more times until the de

sired Zone 2, 3, or 4 status appears in

the OSD and front panel displays.

2. Within 10 seconds, adjust the volume

control on the front panel or remote to

change the remote zone output level. The

new setting appears in the display.

3. Following 10 seconds with no commands,

the RSP-1069 reverts to normal opera

tion.

NOTE: You can disable the ability to control

remote zones from the main room remote

control by changing the DISCRETE setting on

the Other Options Menu from NO to YES.

After changing the setting, all commands from

the main room remote control change only

the main room, even when a remote zone is

selected for control.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 89 90

Kommentare zu diesen Handbüchern

Keine Kommentare

Rotel RSP-1069 Bedienungsanleitung Seite 35

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Empfänger und Verstärker Rotel RSP-1069